Unitec Sentine Installation Manual User Manual

Sentinel Installation Manual Unitec 443-561-1200 • www.StartwithUnitec.com

SENTINEL Document Number: SENT1001 6 Document Name: Sentinel Installation Manual Circuit Description Wire Qty Wire Requirements Sent

SENTINEL Document Number: SENT1001 7 Document Name: Sentinel Installation Manual 2 Mechanical Installation 2.1 Hardware Required Prior

SENTINEL Document Number: SENT1001 8 2.3 Base Installation  Note: Pull all wires through conduits before mounting the base. See Elec

SENTINEL Document Number: SENT1001 9 Figure 5. Sentinel Base with Mounting Plates When the base is to be surface mounted, the legs of

SENTINEL Document Number: SENT1001 10 Document Name: Sentinel Installation Manual 2. Carefully set the Sentinel on top of the base so

SENTINEL Document Number: SENT1001 11 Figure 6. Sentinel Interior 3.4 Connecting Power 1. Locate main power wires. There will b

SENTINEL Document Number: SENT1001 12 Figure 7. Neutral - Ground – Line Connections 4. Use wire ties to route and secure any extra

SENTINEL Document Number: SENT1001 13 3.6 Wash Control Wiring 3.6.1 Overview In applications where the Sentinel will communicate with

SENTINEL Document Number: SENT1001 14  Note: “Wash Output #”refers to the number associated with the arming wires. Refer to the wash

SENTINEL Document Number: SENT1001 15 • Make sure all power is disconnected from the wash equipment prior to beginning this procedure.

SENTINEL Document Number: SENT1001 Document Name: Sentinel Installation Manual SENTINEL INSTALLATION MANUAL Revision A This manual provid

SENTINEL Document Number: SENT1001 16 Document Name: Sentinel Installation Manual 3.7 Intercom Systems 3.7.1 Overview The use of an int

SENTINEL Document Number: SENT1001 17 2 Wire Intercom Configuration: This type of intercom system has both the Call Function and audio

SENTINEL Document Number: SENT1001 18 Document Name: Sentinel Installation Manual 4 System Startup For fully detailed instructions, plea

SENTINEL Document Number: SENT1001 19 Document Name: Sentinel Installation Manual [THIS PAGE INTENTIONALLY LEFT BLANK]

Document Number: SENT1001 20 Appendix A. Sentinel Base - Bottom Up View Document Name: Sentinel Installation Manual

Document Number: SENT1001 21 Appendix B. Sentinel Networking Unitec supplies a pre-programmed router for connecting devices as a local net

SENTINEL Document Number: SENT1001 22 When a router (or modem with built-in router) is used between the Unitec router and broadband co

SENTINEL Document Number: SENT1001 23 • Terminating Ethernet Cables 1. Carefully remove the outer jacket of the cable. Be careful wh

SENTINEL Document Number: SENT1001 24 3. Untwist the pairs so they will lay flat between your fingers. The white piece of thread can b

SENTINEL Document Number: SENT1001 25 5. Keep the wires flat and in order as you push them into the RJ-45 plug with the flat surface o

SENTINEL Document Number: SENT1001 i Document Name: Sentinel Installation Manual Table of Contents 1 Site Planning and Preparation ...

SENTINEL Document Number: SENT1001 26 could lead to headaches down the road. Also, crossed wire pairs could lead to physical damage of

SENTINEL Document Number: SENT1001 27 Appendix C. POS Interface External POS Option The external POS option allows wash codes to be pu

SENTINEL Document Number: SENT1001 ii Document Name: Sentinel Installation Manual Appendix A. Sentinel Base - Bottom Up View ...

SENTINEL Document Number: SENT1001 1 1 Site Planning and Preparation 1.1 Introduction This chapter provides guidelines for planning the

SENTINEL Document Number: SENT1001 2 Document Name: Sentinel Installation Manual 1.2 Positioning the Sentinel 1.2.1 In-Bay Application

SENTINEL Document Number: SENT1001 3 Figure 1. Express Exterior Island Document Name: Sentinel Installation Manual

SENTINEL Document Number: SENT1001 4 1.3 Electrical Preparation 1.3.1 Conduit Installation A typical installation will require 3 condui

SENTINEL Document Number: SENT1001 5 Figure 3. Bottom View of Base 1.3.2 Power Requirements The Sentinel requires 120 VAC, 8 Amps se